• ODT Gun Show & Swap Meet - May 4, 2024! - Click here for info

Search results for query: *

  1. A400 XCEL bolt will not close

    It’s going back to Beretta. Hopefully it won’t be gone too long I’ll go back to shooting my Browning For now.

  2. A400 XCEL bolt will not close

    Thanks for the suggestion. I'll give that a try.

  3. A400 XCEL bolt will not close

    The bolt on my A400 will not close. I was on a Dove hunt this past weekend running 3" high brass #7s. During the 30 or so rounds I shot there were 3 instances of the bolt not closing which were easily remedied by pushing the bolt release. The final instance the bolt will not travel forward at...

  4. Sig Sauer p250

    You can buy a P320 slide and trigger group and install it in a P250 frame. The magazines will also interchange. It would be cheaper to buy a P320 if that's what you're looking for.

  5. Sig Sauer p250

    It’s a double action only pistol which is why the trigger is so long and it requires a full extension for reset. If you want something shorter you can get a P320 which is the same frame but striker fired. There are no aftermarket kits to shorten the length of the trigger travel to the best of...

  6. Any Coonan experts?

    He beat me to it. There’s supposed to be a lighter recoil spring for when shooting .38s. I thought Wolff would have them but I just checked their website and they only have the .357 rated 22 # spring. Numrich was a bust as well.
  7.

    New life for a 686 cs-1

    Thanks. I’ll give that a look.
  8.

    New life for a 686 cs-1

    Thanks. I'm always looking for alternatives. The process of applying Blue Remover and then cleaning it off the gun is a royal pain. :)
  9.

    New life for a 686 cs-1

    If I were to want to strip down and refinish a blued gun, would this method work to remove the old bluing better than traditional chemical methods?
  10.

    New life for a 686 cs-1

    Very nice work! Now I want a bead blaster!
  11.

    S&W model 10 build

    What was the issue that the cylinder wouldn't close?
  12.

    S&W model 10 build

    So everything but a barrel? ETA: Looks like they are setup for snubby barrels with the short ejector rod. This would be a good way to build a 3" gun if one could source the barrels.

  13. Beretta 92 .22lr conversion slide, G conversion?

    In for info.

  14. 586 Cylinder ejection sticky

    Sounds like either your ejector rod is loose or you have trash under the extractor star. Check the ejector rod to see if it's tight. Be careful as some have left hand threads. Check under the extractor star. If there's anything there clean it out.

  15. 586 Cylinder ejection sticky

    Are you referring to the cylinder releasing from the frame of the gun or ejecting spent brass from the chambers?
  16.

    Hammer Nose Bushing Install Help for a S&W 30

    According to the guys on the IDPA forums it's a press fit. It should tap out towards the barrel and then tap back in the opposite direction. No videos that I saw but I didn't read the entire thread. https://www.tapatalk.com/groups/idpaforum/firing-pin-bushing-t4335.html You can also send it...

  17. Anyone do good S&W revolver work near Athens / Buford / Gainesville

    Have any of those projects been a s&w revolver? I’m asking because it’s good to have a resource handy but working on revolvers is a fair bit different than autoloaders and rifles.

  18. How to remove front sight CZ P07 gen 1, "Duty"

    You're welcome. I hope it helps.

  19. How to remove front sight CZ P07 gen 1, "Duty"

    I swapped out the sights on my Gen 1 prior to trading it off. It’s been quite some time but I believe that it slots from the front of the slide and there is no set screw on the factory, plastic sight, it should just drive out from back to front. The replacement Dawson sight I installed had a...

  20. Anyone Use The Wheeler Sight Tool?

    I just stopped in to read all the good comments folks were saying about me. :D Just kidding, I have no affiliation with Wheeler tools.
Back
Top Bottom