• ODT Gun Show & Swap Meet - May 4, 2024! - Click here for info

tools

  1.

    North East GA  FS Generator

    REDUCED! Briggs and Stratton Generator. 6250 watts, 8500 starting Watts. Has 30 hours on it give or take 1 or 2. Co Guard. Comes with a fuel tank of fuel and instruction manuel. Paid $825 for it new asking $580.00 for it. Used during one storm and it ran most of my house. Changed oil as...
    • Price: $580

  2. North West GA  FS Mi-T-M Kerosene multi fuel forced air heater

    I have up for sale only a Mi-T-M portable kerosene forced air heater. Fires right up Works perfectly. Factory Tested for Multiple Fuels built-in temperature control and sure start ignition Kerosene · JP8/Jet A fuel · No. 1 or No. 2 fuel oil · No. 1 or No. 2 diesel fuel · Not approved for bio-fuel
    • Price: $300

  3. FS Dewalt cordless chainsaw

    New in the box saw! Tool only. No battery or charger.
    • Price: $150

  4. Central GA  FS/FT Fs/Ft Milwaukee portaband , Metal shears ,Stud welder

    Milwaukee heavy-duty portable bandsaw Extra blades included $250 Milwaukee heavy-duty 18ga Metal shears $150 H&S tools 4500 Stud welder Box of studs Pull hammer $150 Sell or trade Trades Glocks in 9mm Rifles in 308,223
    • Price: $250

  5. Metro Atlanta  FS/FT Dewalt 18v Kit + Black and Decker 24v Firestorm Kit

    Hey all, for trade or sale are 2 different tool kits. Both function great, albeit the batteries are a bit old. The 18v Dewalt kit includes drills, hammer drill, light, 4 batteries, 2 chargers, and I can throw in a box (it is from another kit however). The 24v Black and Decker Firestorm kit...
    • Price: $230

  6. Metro Atlanta  FT *New* Senco Finishpro 35/Finishpro 15/SLS15 Finish Nailers and Stapler Set

    Hey all, for sale is a brand new Senco set (no box but never been used). Includes a Finishpro 35, Finishpro 15, and a SLS15. Tools are metal construction from a few years back so much higher quality than new production ones where they use lower quality internals. Includes a rolling bag. Not...
    • Price: $0

  7. North East GA  FS/FT CM - Cyclone 1/2 Ton Chain Hoist - Model-M

    I have for sale or trade a CM Cyclone 1/2 ton chain host . Model -M in good working condition. Always keep inside. Thanks for looking.
    • Price: $170

  8. North West GA  FS DeWalt 7 inch polisher/buffer

    Used a couple times on a project. Paid $229 a couple months ago. You can have the pad that’s on it. I don’t get on this site often enough anymore so just text if interested. I’ll check PM’s occasionally 7062990948
    • Price: $100

  9. North East GA  FS Briggs & Stratton Storm Responder

    Briggs and Stratton Generator, Storm Responder. 6250 watts, 8500 starting Watts. Has 30 hours on it give or take 1 or 2. Co Guard. Comes with a fuel tank of fuel and instruction Manuel. Paid $825 for it new, asking $525.00 for it. Used during one storm and it ran most of my house. Changed oil as...
    • Price: $525

  10. South East GA  FS/FT Used Snap-On and Blue-Point tools - Trades added

    For sale I have some used Snap-On and Blue-Point tools that I have duplicates of. Now that I'm not turning wrenches for a living anymore, I am looking to move these along to someone who can use them. I am good with most methods of payment. 3 piece Blue-Point 1/4" drive locking extensions - $75...
    • Price: $35

  11. South East GA  FS/FT Matco and MAC compression tester - Trades added

    For sale I have a LNIB Matco compression tester (#CT110K) and a used MAC compression tester (#CT25). The Matco tester I bought from a local tool truck around 2017-2018 when I was still turning wrenches for a living. I'm pretty sure I only used it once or twice. The MAC tester I found in a...
    • Price: $25

  12. North West GA  FS/FT Misc lot of tools

    Everything you see in the pic for $20. The puller isn't currently turning.
    • Price: $20

  13. South East GA  FS Stanley-Bailey no 6 fore plane

    Cleaned up and refitted to original specs. Note sample shaving of Birdseye maple. If I were to sand a work piece I just planed, I would start at 800 grit. Price includes flat rate shipping. $125
    • Price: $150

  14. North East GA  FS/FT Jet Wood Lathe 10x15

    Jet Wood Lathe 10”x15” never been used. Has just sat in the basement since I bought it. $500 OBO
    • Price: $500

  15. Metro Atlanta  FS NIB Milwaukee shear

    NIB Milwaukee 18 gauge shear.
    • Price: $125

  16. Central GA  FS/FT Fs/Ft Walter zip wheels 11-T 062

    Fs/Ft 3- 25 count box's 75 total disc These will cut 1/2" SS sheets like butter and will not shatter Best cutting wheels hands down 1 disc will cut 3-4 cars in half no issues Never buy disc agian May trade ? $125 per 25 CT box $375 for all 3 box's 75ct shipped Insurance for shipping...
    • Price: $125

  17. Item Gone: FS/FT Tin snips

    9 pair assorted tin snips and 2 bonus rivet guns. Used.
  18.

    North East GA  FS Iwata LPH400 and spare clone...$450

    Got a brand new Iwata LPH400 with a clone for clear when i was going to paint my truck and have since lost all interest in both...gunnis brand new in the box with a cup kit and the clone is new but missing the box for some reason...asking well under what i paid for them and anyone that does...
    • Price: $450

  19. North East GA  FS Evo Rage 2 cold chop saw...$175

    Got this to build the frame of my truck and now have no need for it since the truck frame never got started...used it once or twice to check square and then never touched it again...blade is still sharp as a razor and works amazing...cuts thru 2x4, 1/4" wall steel like butter...new these are...
    • Price: $175

  20. Central GA  FS Arm and hammer blacksmiths anvil

    Arm and hammer blacksmiths anvil I think it’s 92 pounds in great shape has good rebound mist pick up near Griffin Ga
    • Price: $425
Back
Top Bottom