• ODT Gun Show this Saturday! - Click here for info and tickets!

Search results for query: *

  1.

    How to remove Glock front sight when screw is gone?

    run a few mags thru it. it will fall out.. or change your mind and decide to keep it, then it will fall out and you wont find it...

  2. 300 BO not locking back

    before you go rebuilding your upper, playing with gas ports, or anything else. check your buffer. a lot of cheaper buffers will cause problems. i just fixed a 300 bo for a buddy. it would fire and eject but not chamber the next round, occasionally he could get 2 or 3 rounds, but most times just...

  3. Glock work in the norcross area

    sometimes its just worth a 20 mile trip.

  4. Pin and weld remove to install a new muzzle device.

    may be cheaper in the long run to swap out the barrel. then sell the pinned one to someone else....

  5. Pin and Weld Cost

    i done a few myself. i just clock the flash hider,lock it in the vise,drill it about 3/4 way thru. snap the bit off and weld the hole up. touch up with a little paint. but thats for my personal stuff....
  6.

    Double barrel rescue from flood

    yea for it to split half way up like that. seems like with plastic/paper wadding and bird shot,it would be hard to build that kind of pressure thru a 12ga hole without blockage..
  7.

    Double barrel rescue from flood

    that sucks. check the proof marks on it. if he was running modern ammo,the loads may have been way too hot. or in the past it had seen a lot of slugs thru a choked barrel. what was he hunting? dove and quail with low brass 7 1/2 or geese with high brass steel?
  8.

    Double barrel rescue from flood

    if the barrel has proofs on it,it should be fine to shoot approved ammo. its not like its rusted thru or thin. shotguns are tough,even cheap ones. so a lc smith is a sledge hammer. if the bores are rusty,run some red scotch brite thru them,clean the up and shoot it. it the internals are frozen...
  9.

    How big a pain in the ass is this red Loctite going to be?

    do you want to keep the tube? if you are not worried about it,lock the lower in a vice with a vice block. heat the ever livin crap out of the tube. unscrew it with a pair of channel locks. spray paint the tube black. sell in on here "anib" for 3 times the cost of a new one. but a new one and...

  10. Milling of Glock slide

    full blown has done 3 for me. even milled a 17 to take the mos plates... they do great work...

  11. AR Smith near Winder

    ar's are super simple. dont be afraid to tackle it yourself. look at a video you should be able to do it. its always a good idea to be able to maintain your rifle....

  12. Curious. Eotech

    pics??

  13. Dead night sights

    just microwave them. or you can open the back of an old tube TV. you will find radiation warning sticker,crack that part open ,reach in,and smear it on the sights. good to go..you can also rub it in your eyes and be able to see in the dark... disclaimer this was a joke,and not a very good one...

  14. Barrel cutting and threading

    i was gonna say full blown firearms as well. looks like a couple of guys beat me to it.. real good guys and great work...

  15. Slide milling for an RMR

    little bit of a drive. but Full Blown Firearms in Hampton. they are about a half mile from the Atlanta motor speedway.. they do some great work..

  16. Any folks out there threading a shotgun barrel?

    full blown firearms in hampton have you thought about one of the adjustable chokes? you can run,bird,buck,and slugs thru them. they can be had pretty cheap. i know some guys dont like them,but they are great for the "pack gun"set up...

  17. Barrel Threading on the south side of the ATL.

    or panicking to get that last gift. or just happy to escape the house full of family. or happy to show your bro in law from California how America looks... but yea,kinda late but always a fun show...

  18. Barrel Threading on the south side of the ATL.

    that 2000+ table gun show. Dec 21-22 GA, Atlanta. Atlanta Expo Center, 3650 Jonesboro Rd

  19. Barrel Threading on the south side of the ATL.

    thats Brad for ya. Jeremy is one heck of a machinist as well. good guys at Full Blown. if you guys want to meet Brad,he will have a table beside me at the Joneseboro rd show in December...
  20.

    so i am at Ed's a few months back

    they wont fit.. maybe those little rubber balls from the gum machines.
Back
Top Bottom